Router#sh inv NAME: "2811 chassis", DESCR: "2811 chassis" PID: CISCO2811 , VID: V05 , SN: FHK1235F44B NAME: "Thirtytwo Port Low-Speed Async on Slot 1", DESCR: "Thirtytwo Port Low-Speed Async" PID: NM-32A , VID: V01, SN: 36611983 Router# Router#sh line Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns * 0 0 CTY - - - - - 1 0 0/0 1 1 AUX 9600/9600 - - - - - 0 0 0/0 1/0 66 TTY 9600/9600 - - - - - 0 0 0/0 1/1 67 TTY 9600/9600 - - - - - 0 0 0/0 1/2 68 TTY 9600/9600 - - - - - 0 0 0/0 1/3 69 TTY 9600/9600 - - - - - 0 0 0/0 1/4 70 TTY 9600/9600 - - - - - 0 0 0/0 1/5 71 TTY 9600/9600 - - - - - 0 0 0/0 1/6 72 TTY 9600/9600 - - - - - 0 0 0/0 1/7 73 TTY 9600/9600 - - - - - 0 0 0/0 1/8 74 TTY 9600/9600 - - - - - 0 0 0/0 1/9 75 TTY 9600/9600 - - - - - 0 0 0/0 1/10 76 TTY 9600/9600 - - - - - 0 0 0/0 1/11 77 TTY 9600/9600 - - - - - 0 0 0/0 1/12 78 TTY 9600/9600 - - - - - 0 0 0/0 1/13 79 TTY 9600/9600 - - - - - 0 0 0/0 1/14 80 TTY 9600/9600 - - - - - 0 0 0/0 1/15 81 TTY 9600/9600 - - - - - 0 0 0/0 1/16 82 TTY 9600/9600 - - - - - 0 0 0/0 1/17 83 TTY 9600/9600 - - - - - 0 0 0/0 1/18 84 TTY 9600/9600 - - - - - 0 0 0/0 1/19 85 TTY 9600/9600 - - - - - 0 0 0/0 1/20 86 TTY 9600/9600 - - - - - 0 0 0/0 1/21 87 TTY 9600/9600 - - - - - 0 0 0/0 1/22 88 TTY 9600/9600 - - - - - 0 0 0/0 1/23 89 TTY 9600/9600 - - - - - 0 0 0/0 1/24 90 TTY 9600/9600 - - - - - 0 0 0/0 1/25 91 TTY 9600/9600 - - - - - 0 0 0/0 1/26 92 TTY 9600/9600 - - - - - 0 0 0/0 1/27 93 TTY 9600/9600 - - - - - 0 0 0/0 1/28 94 TTY 9600/9600 - - - - - 0 0 0/0 1/29 95 TTY 9600/9600 - - - - - 0 0 0/0 1/30 96 TTY 9600/9600 - - - - - 0 0 0/0 1/31 97 TTY 9600/9600 - - - - - 0 0 0/0 514 514 VTY - - - - - 0 0 0/0 515 515 VTY - - - - - 0 0 0/0 516 516 VTY - - - - - 0 0 0/0 517 517 VTY - - - - - 0 0 0/0 518 518 VTY - - - - - 0 0 0/0 Line(s) not in async mode -or- with no hardware support: 2-65, 98-513 Router# Router#sh run int lo0 Building configuration... Current configuration : 67 bytes ! interface Loopback0 ip address 10.10.10.10 255.255.255.255 end Router# Router(config)#line 1/0 1/7 or line 66 73 Router(config-line)#transport input telnet Router(config-line)#exit Router(config)#ip host fw1 2066 10.10.10.10 Router(config)#ip host sw1 2067 10.10.10.10 Router(config)#^Z Router# Router#fw1 Trying fw1 (10.10.10.10, 2066)... Open ciscoasa> [Ctrl+Shift+6, x] Router#sw1 Trying sw1 (10.10.10.10, 2067)... Open Switch> [Ctrl+Shift+6, x] Router#where Conn Host Address Byte Idle Conn Name 1 fw1 10.10.10.10 0 0 fw1 * 2 sw1 10.10.10.10 0 0 sw1 Router# Router#sh line | in 1/0 | 1/1 * 1/0 66 TTY 9600/9600 - - - - - 1 1 0/0 * 1/1 67 TTY 9600/9600 - - - - - 1 1 0/0 Router#
The CAB-OCTAL-ASYNC Cable
Terminal servers provide out-of-band access for the management of asynchronous devices.
No comments:
Post a Comment